661 cyclops Remote Alarm

This remote control alarm is operated by multi code remote control. Entry point protection of doors, boot and bonnet with a shock sensor. Audible warning is achieved via a standard 115dB siren, visually via the vehicle indicators and via a dash mounted high intensity red LED. The system may provide keyless entry and a source of immobilisation.

Arming procedure while ignition is off
i

The system will arm immediately if the main button of a valid remote control is momentarily pressed, the doors will lock and all security functions will become active.

Disarming procedure

The system will disarm when the main button of a valid remote control is pressed

Immobilisation Circuit

The system features a 30 Amp rated, normally closed immobilisation circuit, which breaks engine critical signals in the vehicle. Starter motor, fuel pump, fuel injection, main ignition are commonly immobilised circuits

Safety circuitry in case of power failure

System sources alternate power from ignition if main power is lost

Component protection against harsh road conditions

All relays are fully encapsulated to provide protection against dust and moisture

System memory

Allows system to track two controllers

Controller re-programming

Service technician can delete lost or stolen controllers from memory

Plug and play for service

Designed to allow easy access for service technicians. Plugs and sockets are located inside the main control module to protect against access by thieves

Emergency Personal Identification Number (PIN) override
P

Enter the secret two digits to override the immobiliser

Alterable PIN
P

A factory programmed PIN comes standard with each system. It is recommended the owner of the system changes the PIN to a new, easily remembered number

Super bright red dash LED

This LED flashes to inform user when system is armed. The LED is mounted on the driver's side dash and is visible from outside the window

Arm/Disarm confirmation

System flashes car indicators when arming or disarming

Alarm illumination

System flashes car indicators when thief triggers alarm

Trigger diagnostics

System will flash indicators to report the last triggered circuit

Standard siren

Uses standard two wire 115dB siren

Arm/Disarm confirmation
P

System sounds a siren when arming and disarming

Temporary arm/disarm chirp disable

Momentarily press the second button of the remote control before pressing the main button, the siren will not chirp during that one operation

Doors, bonnet and boot monitoring
i

Triggers alarm system if intruder opens any protected entry point in vehicle

Accepts plug-in single stage shock sensor

Sensor measures vibration subjected to vehicle to detect intruder.

Locks and unlocks all doors

System can trigger factory central locking, aftermarket central locking or central locking relays

Variable pulse time
P

Extend pulse length to drive pneumatic central locking systems (Mercedes).

Automatic re-locking
iP

System will re-arm and re-lock doors if previously disarmed by remote control and doors remain closed

Anti-hijacking protection
iP

System locks doors when ignition is turned on, unlocks when ignition is turned off.

Current draw

<10mA average while armed. <150mA disarm (and for no more than 39 seconds after ignition is switched off).

Wide Operating voltage

Operating voltage +9VDC to +15VDC

Operating temperature

-20 degrees to +85 degrees for equipment designed to be installed within vehicle cabin

Operating temperature

-20 degrees to +105 degrees for equipment designed to be installed inside engine compartment

Polarity protection

The system circuitry is design to protect itself against accidental battery polarity reversal. This can happen when replacing the vehicle battery

Independent indicator power fuse

System uses independent fuse to power indicators, ensures short circuit in indicator circuit does not affect system operation

Short circuit protection

The power supply wire to the system is protected against an internal fault within the system

Panic / Car Finder

Press and hold second button of remote control to cause siren to sound and indicators to flash

Electric window closer
i

Provides signals used by electric window closers, system will close all electric windows when armed by remote control

Electronic boot release
i

Press and hold the secondary remote control button to activate boot release output. The indicators will flash four time each time the boot release signal is sent.

Installation Guide

Complete installation guide and specifications for the 661-3(NWH).

Installation Guide

Complete installation guide and specifications for the 661-3.

Installation Guide

Complete installation guide and specifications for the 661.

User Guide

Informs the end-user of the system's functions, features and limitations.

Manufacturers warranty on Control module
i

Guarantees control module is free from manufacturing defects for 24 months from time of purchase

Manufacturers warranty on Sundry items
i

Guarantees remote controls, siren and sundry items are free from manufacturing defects for 12 months from time of purchase

Manufactured in ISO9001 facility

Built within world standard production facility